Juma: /* Fire Protection */

2022-07-21T13:31:38Z

Fire Protection

Juma: /* MISCELLANEOUS BUILDING WORKS */

2022-07-21T12:52:10Z

MISCELLANEOUS BUILDING WORKS

Juma: /* MISCELLANEOUS BUILDING WORKS */

2022-07-21T12:50:32Z

MISCELLANEOUS BUILDING WORKS

Juma: /* Hardware Description */

2022-07-21T12:17:42Z

Hardware Description

Show changes

Juma at 12:04, 21 July 2022

2022-07-21T12:04:52Z

Juma: Created page with " 8 MISCELLANEOUS BUILDING WORKS 8.1 Scope This specification covers the general requirements for, but is not limited to, sundry items, finish hardware, sanitary installation,..."

2022-07-15T10:18:55Z

Created page with " 8 MISCELLANEOUS BUILDING WORKS 8.1 Scope This specification covers the general requirements for, but is not limited to, sundry items, finish hardware, sanitary installation,..."

Show changes

@@ Line 173: / Line 173: @@
 The following arrangement criteria shall be met:<br>
 •	Maximum travel distance to an extinguisher:22 m<br>
-•	Maximum areas to be protected per extinguisher:500 m2
+•	Maximum areas to be protected per extinguisher:500 m<sup>2</sup>
 ==Disinfection==
 ===General===

@@ Line 1: / Line 1: @@
-=MISCELLANEOUS BUILDING WORKS=
+=miscellaneous building works=
 <div style="text-align:justify">
 ==Scope==

@@ Line 1: / Line 1: @@
 =MISCELLANEOUS BUILDING WORKS=
 ==Scope==
 This specification covers the general requirements for, but is not limited to, sundry items, finish hardware, sanitary installation, fire protection and disinfection.
@@ Line 191: / Line 192: @@
 After the structure has been filled, the strength of the chlorinated water shall be determined by the Engineer.  If the chlorine residual is less than 1 ppm, an additional dosage shall be applied to the water in the structure.
 If the residual is greater than 2 ppm, the structure shall be partially emptied and additional clean water added.  In no case shall water be released through the drain lines prior to the end of the required retention period. Any obvious leaks which appear during filling shall be repaired before continuing.

@@ Line 1: / Line 1: @@
+=MISCELLANEOUS BUILDING WORKS=
-	MISCELLANEOUS BUILDING WORKS
+==Scope==
 This specification covers the general requirements for, but is not limited to, sundry items, finish hardware, sanitary installation, fire protection and disinfection.
+==Sundry items==
-.2	Sundry items
+===Drying and Cleaning===
 Upon completion, the Contractor shall thoroughly brush and wipe down to remove dust, etc., and clean the finishing works so that they are left in a condition to the satisfaction of the Engineer.
-.2.2	Fixing to Structures. Brick and Concrete Etc.
+===Fixing to Structures. Brick and Concrete Etc.===
 Where fixings to structures previously constructed are to be made by setting a bolt system into preformed holes, such fixings shall be made either by rawlbolting or by using an approved proprietary resin anchor system.  Where thin sections are involved or where stresses are likely to be set up which might cause damage to the structure, the use of the resin anchor system only will be permitted.  Only in special circumstances will the Engineer permit rag bolts to be used.
 Where connections are to be by "casting-in" techniques, the "cementing-in" sockets used with the rawlbolt system or other approved bolt systems shall be accurately set to template prior to placing the surrounding concrete and shall be kept rigidly in place until the concrete has properly set.
 Where resin anchorage is used the Contractor shall ensure that the setting time of the resin is appropriate to the requirements for setting up, plumbing and aligning the work before it sets.  Bolts shall be set to template and hole diameters shall conform to the recommendations of the suppliers.
 Whatever system is used, all bolts shall be cadmium plated.  Where aluminium and steel are combined in any fixing system all mating surfaces shall be treated with a zinc-chromate based jointing compound prior to connecting.
-.2.3	Metal Windows, Louvres and Doors
+===Metal Windows, Louvres and Doors===
 Metal windows and doors shall be handled with care and until fixed shall be stacked on edge on clean surfaces.
 In brick openings, frames shall be fitted with fixing lugs in adequate number, and bedded in mortar.
@@ Line 19: / Line 17: @@
 Frames shall not be used as centring for brickwork or to support a lintel.
 Frames shall be carefully pointed in 1:3 cement mortar and, after raking out the gap, shall be pointed with mastic.
-.2.4	Kind of Windows and Doors
+===Kind of Windows and Doors===
 When not otherwise specified, the Contractor shall use aluminium windows which shall be robust and of good quality.
 Extruded aluminium members shall be fabricated conforming to DIN 1784.
@@ Line 25: / Line 23: @@
 The main elements of the aluminium solid section out frame shall be at minimum tolerance not less than 2.0 mm thick.  The thickness of all other structural elements of the sections shall be at minimum tolerance not less than 1.2 mm except for weather-stripping retaining flanges and glazing beads which may be thinner.
 All aluminium alloy parts shall be finished satin matt and anodized in accordance with DIN 4113.
-Weather-stripping shall:
+Weather-stripping shall:<br>
-•	be made from materials known to be compatible with aluminium;
+•	be made from materials known to be compatible with aluminium;<br>
-•	not shrink or warp or adhere to sliding surfaces or closing surfaces;
+•	not shrink or warp or adhere to sliding surfaces or closing surfaces;<br>
-•	not promote corrosion when in contact with the aluminium alloy used; and,
+•	not promote corrosion when in contact with the aluminium alloy used; and,<br>
-•	be resistant to deterioration by weathering.
+•	be resistant to deterioration by weathering.<br>
 Joints in frames shall be made neatly and accurately either by welding or by mechanical means (e.g. cleating and screwing) and may have flush, stepped or lapped surfaces.  Welded joints shall be cleaned of f smooth on the surfaces which are exposed when the window or door is in the closed position or where they come into contact with glazing.
 Hinges and pivots shall be either of suitable corrosion-resistant materials or, if not compatible with aluminium, shall be separated from the aluminium by materials which are compatible with it.  Hardware, including fixings, shall be of suitable corrosion-resistant materials.  Materials or finishes which are not compatible with aluminium shall not be used unless they are satisfactorily separated from the aluminium by materials which are compatible with it.
@@ Line 35: / Line 33: @@
 Windows and doors shall be such that glazing and reglazing on site is possible without the need to remove the outer frames from the structure of the building.
 Mosquito screens shall be fitted to all windows and external doors.
+==Finish Hardware==
-.3	Finish Hardware
+===General===
 The Contractor shall furnish and install all finish hardware to complete the work as specified.
 The Contractor shall submit samples of all hardware to the Engineer for approval.
@@ Line 44: / Line 41: @@
 Quantities, weight and sizes specified herein are the minimum that will be acceptable.
 Finish of all hardware shall be dull stainless steel unless otherwise noted.
-.3.2	Hardware Description
+===Hardware Description===
-Locks:
+Locks:<br>
-)	Tabular cylinder locks: stainless finish
+)	Tabular cylinder locks: stainless finish<br>
-)	Entry, exit and office doors: keyed on side, button opposite side
+)	Entry, exit and office doors: keyed on side, button opposite side<br>
-Passage doors 	knobs both sides, no lock
+Passage doors 	knobs both sides, no lock<br>
-Storage room: 	single knob with key
+Storage room:single knob with key<br>
-Toilet room:  	stainless outside, chrome inside, pin opening outside for emergency with button inside.
+Toilet room:stainless outside, chrome inside, pin opening outside for emergency with button inside.<br>
-All keyed locks to be master keys for same building.
+All keyed locks to be master keys for same building.<br>
-All locks to have two keys each.
+All locks to have two keys each.<br>
-Door closers:   	heavy duty type with stainless cover; top installation for either right or left hand operation
+Door closers:heavy duty type with stainless cover; top installation for either right or left hand operation<br>
-Stops:    	floor or wall mounted type, stainless
+Stops: floor or wall mounted type, stainless<br>
 Upon completion of the hardware installation, all items shall be inspected for proper operation.  All work shall be protected and any damage or incorrectness shall be repaired.
 Hardware shall not be fitted until the latest time in the Contract.

MISCELLANEOUS BUILDING WORKS - Revision history

Juma: /* Fire Protection */

Juma: /* MISCELLANEOUS BUILDING WORKS */

Juma: /* MISCELLANEOUS BUILDING WORKS */

Juma: /* Hardware Description */

Juma at 12:04, 21 July 2022

Juma: Created page with " 8 MISCELLANEOUS BUILDING WORKS 8.1 Scope This specification covers the general requirements for, but is not limited to, sundry items, finish hardware, sanitary installation,..."